RBX1600 1.0.3

Issue:
	If, during equipment setup, power is applied to the RBX1600 before the Sony Megachangers 
	are connected to RBX1600. The RBX1600 fails to recongize the Megachangers and may hang.

Workaround:
	Perform a soft reset of the RBX1600 using on of the following methods:

	1) From the HADES user interface, push "Manage" button, and select the "Reboot Device" 
	   button.

	2) Press an hold the RBX1600 power switch for 10 seconds or until the power light 
	   starts flashing.

	3) Remove and reapply power to the RBX1600

Issue:
	HADES Client and the RBX1600 fail to play discs or tracks if a Sony Megachanger is 
	configured to use Command Mode CD2 or CD3.

Workaround:
	Change all Sony Megachangers to use Command Mode CD1. See your Sony Megachanger users 
	manual for how to do this.
	
Issue:
	Discs are missing from the Disc List in the Now Playing, Play Editor and Disc Editor
	views.
	
Workaround:
	The Disc List shows all unique discs found in all players attached to the RBX1600. A Disc
	is unique if it's DISC ID (as calculated by freedb.org) is unique.  Discs with duplicate 
	DISC IDs are dropped without warning from the Disc Lists.  This behavior is intended and
	there is no work around.  A follow on release will display a warning dialog reporting
	duplicate DISC ID at start up.
	
	The problem is cause by a FreeDB DISC ID hash resulting in lots of collisions and StreetFire
	is re-evaluating it's implemention in the 1.1 development series with a resolution planned
	for 1.2 stable release.
	
Issue:
	Local edits of FreeDB Disc information with the Disc Editor are lost if the disc is removed
	from the Sony Megachanges.
	
Workaround:
	The behavior is intentional and related to the issue about duplicate DISC IDs.  The is no
	workaround at this time.
	
	StreetFire is re-evaluating it's implemention in the 1.1 development series with a resolution 
	planned	for 1.2 stable release.

Issue:
	HADES Client can not find RBX1600 when a firewall is present between the client and 
	the RBX1600.

Workaround:
	The StreetFire MediaOrb uses a combination of multicast packets and bi-directional TCP 
	connection to perform device discovery and communications.  Typical PC and hardware based
	firewalls block inbound multicast packets and inbound TCP connections.  This causes a device 
	discovery or communications failure which will prevent the RBX1600 icon from display.

	This remedy this, please configure your firewall to allow the following packets through:
	1) Allow in/out of UDP packets with multicast address 239.192.0.1 on ports 
	   46000 and 46001.
	2) Allow in/out of TCP connections on ports 46002, 46003, 46004

	After reconfiguring your firewall, restart both the RBX1600 and the HADES client.

Issue:
	RBX1600 hangs when a Sony Megachanger is unplugged from the RBX1600 or the wall power is 
	removed Megachanger, while the RBX1600 is physically powered.

Workaround:
	Perform a soft reset of the RBX1600 using on of the following methods:

	1) From the HADES user interface, push "Manage" button, and select the "Reboot Device" 
	   button.

	2) Press an hold the RBX1600 power switch for 10 seconds or until the power light 
	   starts flashing.

	3) Remove and reapply power to the RBX1600